一、三叶罗茨风机如何组装？针对“组装”的问题，我们要了解组装的内容，三叶罗茨风机出厂前的组装有两部分内容，一分部是机头的组装，一部分是整机的组装，这些是出厂前的组装；经过组装之后，便可以进行发货了，终端客户在拿到三叶罗茨风机之后，还会对罗茨风机进行管道与风机的连接。

1、 How to assemble a three leaf Roots blower? Regarding the issue of "assembly", we first need to understand the content of assembly. The assembly of the Three Leaf Roots blower before leaving the factory consists of two parts: one is the assembly of the machine head, and the other is the assembly of the entire machine. These are the assembly before leaving the factory; After assembly, it can be shipped, and the end customer will also connect the pipeline to the Roots blower after receiving it.

下面风机针对出厂前的风机组装进行详细的描述：三叶罗茨风机安装的时候需要注意什么问题?

Below is a detailed description of the fan assembly before leaving the factory: What should be paid attention to when installing the Three Leaf Roots blower?

1、机头安装

1. Head installation

风机的机头为组装好的，将组装好的风机机头安装在底座的一侧，然后使用螺栓进行紧固；

The fan head is assembled, and the assembled fan head is installed on one side of the base, and then fastened with bolts;

2、电机安装

2. Motor installation

电机安装在底座的另一侧，安装上去之后，对螺栓稍加紧固，不要立即紧固锁死；

The motor is installed on the other side of the base. After installation, tighten the bolts slightly and do not immediately tighten and lock them;

3、皮带轮安装

3. Belt pulley installation

皮带轮有两部分，一个安装在机头一侧，一个安装在电机一侧，使用设备，对皮带轮进行调整，在装配时，必须要保证机头和电机的皮带轮，在一条纵向线上，不能出现偏差，要调整到在同一水平面上；

The pulley has two parts, one installed on the side of the machine head and the other on the side of the motor. Professional equipment is used to adjust the pulley. During assembly, it is necessary to ensure that the pulleys of the machine head and the motor are on the same longitudinal line, without deviation, and adjusted to the same horizontal plane;

4、皮带安装

4. Belt installation

安装好皮带轮之后，然后安装皮带；

After installing the pulley, proceed to install the belt;

5、紧固螺栓

5. Tighten bolts

紧固电机的螺栓，同时调整罗茨风机皮带的松紧度，调整好之后，然后进行螺栓锁死紧固；

Tighten the bolts of the motor and adjust the tightness of the Roots blower belt. After adjustment, lock and tighten the bolts;

6、安装皮带保护罩

6. Install belt protection cover

上面的安装完成之后，将皮带保护罩安装在底座上面，紧固螺栓即可；

After the installation is completed, install the belt protection cover on the base and tighten the bolts;

7、安装压力表阀

7. Install pressure gauge safety valve

一般厂家为了保证压力表阀不被损坏，可能不会为我们安装，有的厂家可能会对此进行安装；

Generally, manufacturers may not install the pressure gauge safety valve for us to ensure that it is not damaged. Some manufacturers may install it instead;

本文来自：罗茨风机更多的内容请点击：我们将会为您提问的问题提供一个满意的服务，欢迎您的来电！

This article is from Roots blower. For more content, please click: We will provide satisfactory service for the questions you ask. Welcome to call us!